Our brands
See allGuide
About Trucks
Trucks are the steering engine of your skateboard. They connect the wheels to the deck, allow you to turn when you lean your body, and absorb all the impact when you land or grind. A good pair of well-tuned trucks makes the skateboard feel like a different board. In this Collective Store collection, you'll find dozens of Thunder, Independent, Venture, Ace, Iron, and Lurpiv models in various widths and heights, with prices between €25 and €79. Below, we explain how to read each brand's measurements, which height to choose, and how to tune the trucks to your liking.
What you'll find in the truck collection
You'll find polished aluminum trucks, versions with colored baseplates, lighter hollow models, and special editions and collaborations. Some examples:
- Thunder Trucks: the Light Polished II and Team Inverted Polished, in 148 and 149.
- Independent Trucks: the Forged Hollow Mid (159), the Hollow Standard Silver Black (144), and the Chris Colbourn Faces Silver Blue pro model (149).
- Venture Trucks: the All Polished, V-Lights, V8 Pro Koston, V-Hollow High, and editions such as the Venture X Bronze or Venture X Duplex, in 5.6.
- Ace Trucks: the AF1 family in various sizes (33, 44, 55, and 60), in Low, Hollow, and Inverted Hollowed versions, the Ace 55 Classics with a red baseplate, and the Ace X Pass Port AF1 44 Limited Hollow collaboration.
- Iron Trucks: the Iron High Silver in 5.8.
- Lurpiv: another option for those looking for something different.
In most cases, trucks are sold in pairs, enough for one skateboard. Always check the product page.
Anatomy of a truck
Knowing the parts helps you understand the technical specifications and perform maintenance:
- Baseplate: the base that screws onto the deck, with four holes.
- Hanger: the T-shaped piece underneath, where you grind and through which the axle passes.
- Axle: the bar where the wheels and bearings fit.
- Kingpin: the large bolt that connects the hanger to the baseplate and holds the bushings.
- Bushings: the polyurethane rubbers around the kingpin. Their hardness and shape determine how easily the truck turns.
- Pivot cup: the small plastic cup where the end of the hanger fits. When worn, the truck starts to make noise and develop play.
How to choose the truck width
The rule is simple: the axle width should be close to the deck width. This keeps the wheels aligned with the edges of the board. If the truck is too narrow, the wheels are hidden underneath and the skateboard becomes unstable. If it's too wide, the wheels stick out, hit your shoes during flips, and catch on obstacles.
The problem is that each brand uses its own numbering, and none correspond directly to the deck width:
- Independent and Thunder use numbers such as 139, 144, 147, 148, 149, or 159, which correspond to the hanger width in millimeters, not the deck width. Approximately, an Independent 144 usually goes with decks around 8.0 to 8.25, a 149 with 8.25 to 8.5, and a 159 with decks from 8.5 up.
- Venture and Iron use measurements such as 5.2, 5.6, or 5.8, which refer to the hanger width in inches, not the axle width.
- Ace uses numbers such as 33, 44, 55, and 60, where a higher number means a wider truck.
Since the charts vary from brand to brand, check the axle width indicated on each truck's product page or ask us which size is right for your deck. If you don't have a deck yet, choose from the decks first and then come back here.
Height: low, mid, or high
Height is the distance between the deck and the axle. It influences the wheel size you can use and how the skateboard reacts.
- Low: the skateboard sits closer to the ground, is more stable, and pops faster. They are good for technical street and flips, with wheels up to about 53 to 54 mm. Example: Ace 55 AF1 Low or Ace 44 AF1 Low Hollow.
- Mid: the compromise that suits almost everyone, with wheels from 52 to 56 mm. Example: Independent Forged Hollow Mid.
- High: more space between the wheel and the deck, allowing for large wheels (56 mm or more) and looser trucks without wheel bite. Very commonly used in transition and bowls. Examples: Venture V-Hollow High or Iron High.
For choosing wheels, check the diameters and hardness in the wheels collection.
Hollow, forged, and light: what they mean
- Hollow: the kingpin and/or axle are hollow inside. The truck becomes lighter without losing strength for normal use, which is noticeable in flips and the overall weight of the skateboard.
- Forged: the baseplate is forged instead of cast, allowing it to be lighter and stronger.
- Light, V-Lights, and similar: lighter versions of each brand's models, usually with hollow parts or different materials.
How to tune the trucks
The kingpin nut controls the tension of the bushings. Tighten it for the skateboard to turn less and become more stable at speed. Loosen it to turn more easily, at the cost of some stability. Make adjustments a quarter turn at a time and test before adjusting again. A practical rule: the nut should always be fully threaded onto the kingpin, with the tip of the thread at least flush with the nut. Never leave it almost unscrewed.
New bushings are stiffer and soften with use. Give them a few days of sessions before deciding they are too hard. If you still don't like them, there are bushings of different hardness that change the feel significantly.
The axle nuts should be tight enough so the wheel has no side play, but without crushing the bearings. If the wheel stops rolling freely, loosen it slightly. For all this, you need a skate tool (T tool), which you can find in hardware and bearings.
Mounting on the deck
- Place the trucks with the kingpin facing the center of the deck. It is a common mistake to mount one backward.
- Use 7/8" hardware if mounting directly to the deck. If using risers to gain height, switch to 1" or more, depending on the thickness.
- Tighten the nuts in a crisscross pattern, evenly, until the screw heads are flush with the grip tape.
- If you use large wheels or very loose trucks and notice wheel bite, risers are the simplest solution.
Maintenance and wear
- Grinding wears down the hanger. This is normal and does not affect performance until the wear gets close to the axle.
- Cracked or deformed bushings should be replaced, as they make the skateboard unpredictable.
- A worn pivot cup causes play and noise. It is a cheap and easy part to replace.
- A bent or broken kingpin is a reason to stop riding until it is replaced. Do not take risks.
- Avoid water and salt, which oxidize the axle and bearings.
Complete the setup
With the deck and trucks chosen, all that's left are the wheels, bearings, hardware, and a sheet of grip tape. See all the parts together in the skateboard collection. If you prefer a pre-assembled board with trucks sized for the deck, check out the complete skateboards. And to save on the deck, there is the skateboard gear promotion.
Shipping, exchanges, and physical store
Shipping to Continental Portugal costs €5.90 and is free from €59.90, with delivery in 24 to 48 business hours via DPD or CTT. Orders paid by 12:00 PM are dispatched for delivery within the next 24 hours on business days. For Madeira and the Azores, shipping is €12.90 (48 to 72 hours), for Peninsular Spain €8.90 (24 to 48 business hours), for France €12.90 (2 to 4 business days), and for the rest of Europe €18.90 (3 to 7 business days). Prices are in euros including VAT.
You have 30 days from delivery to exchange or return unused trucks in their packaging. Return shipping costs are your responsibility, except in case of a defect or our error, and in Continental Portugal, pickup is scheduled by CTT. The refund is made through the same payment method (MB WAY, Multibanco, PayPal, Visa, or Mastercard).
At the physical store, on Rua Armindo Costa Azevedo Jr, Loja 20, 4785-099 Trofa, you can see the trucks in person, at the same prices as the online store. For questions about measurements, talk to us via WhatsApp or by phone at +351 914 158 783, or by email at info@collectivestore.pt, from Monday to Friday, from 10:00 AM to 12:30 PM and from 2:00 PM to 5:30 PM.
Frequently asked questions about trucks
Which trucks should I choose for an 8.25 deck?
Look for a truck with an axle width close to 8.25. On an Independent, for example, this is usually a 144 or a 149, depending on whether you prefer the wheels more tucked in or more aligned with the edge. For other brands, check the width on the product page or ask us.
Are more expensive trucks better?
Not necessarily for everyone. The more expensive versions are usually lighter (hollow, forged, light) or special editions. To start, a standard model from any of these brands works very well.
Can I use trucks from one brand with wheels from another?
Yes. Skateboard truck axles and bearings are standard size, so any skateboard wheel will fit.
My skateboard doesn't turn much. What should I do?
First, loosen the kingpin nut a quarter turn and test it. If it is still stiff, give the bushings time to soften or replace them with softer ones.
Do trucks come with hardware?
Usually no. Mounting hardware is sold separately. More answers in the frequently asked questions.
Get the width right, choose the height based on the wheels you use, and tune it to your liking. With these steps, trucks will no longer be a question mark and will become the part of the skateboard you know best.
1. How do I choose the truck width?
2. Low, mid or high trucks: which should you choose?
3. What truck brands does Collective Store sell?
4. What are bushings and how are they adjusted?









